Repair Stacks

GLOW Peptide Dosage Chart & Blend Protocol

Updated 2mo ago 6 min read 287+ helpful Calculator

Validity Score

31 Speculative

Evidence 42

Community 100

Completeness 71

Actionability 80

Coverage 80

Penalty -34

This score combines formal evidence, page completeness, calculator readiness, and community convergence.

What it is

GLOW is a fixed 70 mg community blend containing GHK-Cu, BPC-157, and TB-500 — the “GLOW peptide” referred to in community discussion is this three-component blend, not a single compound. The formula combines copper-peptide signaling with two experimental repair pathways, but the blend itself does not have a validated human protocol.

Evidence boundary

Community fixed-ratio blend with no human trial validating the combination or its cycle.

Preparation and measurement

Reconstitution: 70 mg vial + 3 mL BAC = 23.33 mg/mL.

Concentration matches.

Reference schedule

Reference schedule
Phase	Dose	Draw / measure	Frequency	Weekly total
Weeks 1–4	2.33 mg total blend	10 U (0.10 mL)	Once daily	16.31 mg/week

Weeks 1–4

Dose: 2.33 mg total blend
Draw / measure: 10 U (0.10 mL)
Frequency: Once daily
Weekly total: 16.31 mg/week

Weekly totals apply only during the active phase.

Titration rules

The collected schedule uses a fixed 10 U daily draw; no automatic escalation is defined.
Changing the draw changes all three components together. Separate vials are required when one component needs adjustment.

Cycle length and breaks

Use a defined 4-week daily block, then stop for 2–4 weeks and reassess.

What to monitor

Skin and wound changes documented with consistent photos
Pain, swelling, mobility, and injection-site reactions
Avoid duplicate standalone GHK-Cu exposure unless the total copper-peptide amount is explicitly calculated

Practical rules

Keep wound or injury measurements objective and consistent.
Protect healing skin from excess sun exposure.
Record the total weekly GHK-Cu exposure when any separate copper-peptide product is used.

Was this protocol helpful?

Share via

Dosing references

Peptide dosage chart Peptide dose calculator Syringe mixability

Related protocols

KLOW Blend (80 mg) Peptide Protocol & Dosing Tri-Heal Blend (45 mg) Peptide Protocol & Dosing GHK-Cu Peptide Protocol & Dosing BPC-157 + TB-500 (Wolverine) Stack & Dosing

Supply & lot verification Availability and batch-linked COA records for GLOW Peptide Dosage Chart & Blend Protocol are tracked with the current supplier listings. View availability & COA →

Dosing Calculator

70 mg + 3 mL BAC · blend · week 1 2.3 mg

LIVE CALCULATIONvolume / concentration / draw

RP–CALC–01

01 Vial size

02 BAC water

DRAW AMOUNT10 units0.1 mL · U-100

Draw 10 units, equivalent to 0.1 milliliters.

Concentration23.333 mg/mL

Selected dose2.3 mg = 10 units

04 Custom dose

05 Standard amounts

1–10 mg · 0.5 mg steps

06 Suggested doses Select a row

1 unit = 0.01 mL on a U-100 syringe. Values retain decimal precision; visual marks are not silently snapped.

07 cycle summary

Vials required for Cycle

Estimate how much material you need for a full cycle, including cycle length and the number of cycles you plan to run.

Cycle length (weeks) Injections per week Number of cycles

Cycle total —

Total required vials —

Total reconstitution —

Total BAC water —

08 projected levels

How the draws stack up

A first-order model of depot absorption and elimination, run on the draws and cadence above. Pick the half-life from whatever your own source documents — this page does not assume one per compound. A planning sketch — not a prediction for any compound or any individual.

Half-life

Hours

Modelled level across the cycle. Each spike is one draw.

Accumulation—steady state vs one draw

Peak-to-trough—inside one interval

Steady state—about 4 half-lives

Draws modelled—at this cadence

Vial yieldat the selected amount

Draws per vial—

Lasts—

Volume used—

Limiting factor—

Water matrixsame vial, same amount

WaterStrengthDraw

0.5 mL——

1 mL——

2 mL——

3 mL——

5 mL——